Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like aluminum and timber.

It is crucial to wash and oil UPVC windows and doors on a regular basis. This will reduce costly repairs to double glazing and increase energy efficiency.

1. Broken Glass

The broken glass in your windows could cause significant damage to your home and even be fatal. You should take the time to make sure that your windows are in good shape.

For single pane windows, it is fairly easy to replace them, and the replacement is usually able to fit into the frame that was previously installed easily. If you have double glazed window repairs-paned windows which are joined by internal beading, it will be harder to remove and replace the panes that were previously in use. In this situation you'll need to find some plastic spacers to aid the new pane in being able to fit perfectly into the frame of the window.

If you're planning to try to remove the glass panes yourself it is crucial to wear appropriate safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a dropcloth prior to you begin working on the window panes, so that any shards of glass fall onto the fabric, not onto the floor, where they could be trampled under.

Once the glass is removed, it's a good idea to cover the gap with clear packaging tape or duct tape to stop water and drafts from entering the home until a professional is able to come out and fix the window. It also acts as a barrier to prevent any intruders from making their way into your home. If the gap between the door repair near me and the window is large, you might need to consider an alarm system that has windows. This will give you the best of both.

2. Sagging

Upvc is a long-lasting, energy-efficient and affordable alternative to timber sash window. As time passes, they may develop a number of problems that include sliding. A sagging window can cause problems with light, draughts, and even security. It's crucial to act immediately if you notice your uPVC windows are falling down.

Repositioning the hinges could aid in fixing a window which is sliding. You'll first need to open the windows to reach the frame. Then, using a screwdriver, you can take off the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, close your window and check for fitting. If you're satisfied with the fit of your window repair near me, tighten the screws to hold them in place.

If you are unable to move the hinges, you could have to replace the seal. As time passes, rubber seals lose their elasticity and dry out, which causes their tightness to decrease. It is crucial to replace your seal as quickly as you can to ensure that your upvc door repair window waterproof and draughtproof.

UPVC handles can also loosen up. This is often caused by screws that have become undone over time, but it can be due to the handle mechanism wears out. It's fairly simple to fix a loose uPVC handle. First, you'll need to close the window and do an experiment fitting. The corner joints of the sash need to be aligned with the casing joint. If it doesn't then you can make use of a screwdriver to loosen the handle and reverse the mechanism back into its original position.

3. Water Leaks

It is important to take action if you wake up every morning to discover mouldy walls and wet floors. The leaks of water from windows do not only lead to the degrading of the structure of your home but also undermine your efforts to regulate the temperature inside your home. Most of the time, uPVC window leaks are caused by a damaged or missing sealant.

This is a simple fix that can be done by any DIYer who has the ability. Depending on how severe the issue is, old caulking might need to be removed. When it comes to uPVC repair, you must avoid 'over-caulking'. This can make your window more difficult to clean and decrease its energy efficiency.

It is important to check that any drainage holes are free of debris and that the sill pan has been angled in a way that allows it to drain away from the window. In more serious instances, you might have to consider replacing the window.

Other signs of long-term water leakage are rotted sills and the appearance of black spots of mold on the wall near the window. The mold thrives in damp environments and can quickly spread throughout the home.

It is also important to remember that if the leak is coming from between the glass of your double-glazed windows, it's more likely to be a problem with the glass seal, rather than the frame or sagging. Again this can easily be repaired by a uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are stiff to open, or are loose and open with a breeze, it may be hinges at the fault. Anyone with the skills to fix them can replace these in a matter of minutes.

Like any mechanical part hinges will be damaged over time. It is essentially a very simple procedure, but it is easier if you have someone to help you hold the frame up.

Make sure that the uPVC hinges open and close in the proper direction. You can check this by checking for the arrows on each hinge, this shows which way the window should be opened.

The issue could be caused either due to opening the window in the wrong way or due to a poor installation at the factory. This can often be resolved by sending us a photograph on our website. We will be more than happy to give you suggestions.

Regular lubrication of hinges is also essential. Applying an engineering lubricant that is light to the hinges is a good method of doing this. We suggest using the lubricant that doesn't contain solvents, like 3-in-1 Multi-Purpose oil. Regularly lubrication will help the window to operate and close more easily. It can also stop corrosion and reduce the possibility of sticking. The ideal time to do this at least once a year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts in windows made of upvc can be caused by a few different things. The hinges can also become misaligned due to wear, creating a gap where the sash and frame meet. If they are beyond repair, it could be necessary to have them realigned. The interlock may be unbalanced. It is located on the hinge's side and could require to be cleaned. In certain instances it might be necessary to replace them.

These seals can wear down or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with low-emissivity glass, which will help regulate indoor temperatures and again will reduce draughts.

Another, and most effective methods to reduce drafts is to use a draught excluder, these are typically fabric tubes filled with some kind of filler. They can be placed on top of your windowsill. They will help block out cold air and keep your home warm and cosy!

With a little maintenance and repair, your upvc windows will provide an excellent level of security and insulation for your home. However, it is important to recognise that all windows have a lifespan and they may reach an point at which it is more economical to replace them than repair them. If you encounter any issues with your Upvc window you should consult a professional as soon as possible.